Parts & Accessories
The Saris Leveling Block keeps your bike level with your trainer. - Adds stability to your training ride. - For use with any rear wheel-mounted trainer. - Raises front bicycle tire 1.1 inches (2.8 cm) off the ground
Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.
Kurt Kinetic's 12mm Traxle Through-Axle lets you attach your mountain bike to a Kinetic trainer without changing the original skewer. The Kinetic Traxle comes in 3 thread pitches: - T-2101 Coarse: M12 x 1.75mm - T-2102 Medium: M12 x 1.5 - T-2100 Fine: M12 x 1.00mm (Fine XL has the same thread pitch and is a longer version of the fine Traxle)
- Adapter for Tacx Direct Drive trainer - 01 is compatible with 142 x 12mm and 148 x 12mm - 02 is compatible with 135 x 10mm - 03 is compatible with 135 x 12mm (w/5 mm spacer included with every Tacx Direct Drive trainer), 142 x 12mm and 148 x 12mm - 04 The thru axle adapter kit is for bikes with a 12 mm thru axle. The axle adapter is required to couple the rear stay with the thru axle mount on a Tacx NEO or FLUX Smart trainer.
$44.99 - $59.99
The E-Thru Trainer Axle allows the use of a mountain bike in a Tacx trainer. These axles are only suitable for Tacx classic trainers.
The Skyliner is a front wheel support for use with Tacx classic trainers. It raises and supports the front wheel for a natural cycling position and increased stability. It also serves as a handle to carry the trainer.
The Tacx Sweat Cover protects your bike from corrosion caused by perspiration. It is made from absorbent textile to catch and retain perspiration. Its clever design fits all bikes and enables easy mounting.
A sweat cover with a pocket for your smartphone. The sweat cover protects your bike against perspiration and enables the use of a phone while training. The Tacx sweat cover is made from absorbent textile to catch and retain perspiration. Its clever design fits all bikes and enables easy mounting. Suitable for a variety of phone sizes - max. length 138mm, max. width 68mm.
Adapts a thru axle hub bike for a Saris bike trainer. - Trainer Thru Axle Adapter For Saris Trainers - Thread pitch: 1.00 & 1.75 What's Included: - Thru axle - Washers - Endcaps with bolts Trainer Compatibility The Saris Trainer Thru Axle Adapter is designed for indoor use on Saris trainers only and should not be ridden outdoors. Compatible with current basic trainers. Not compatible with CycleOps PowerSync trainers. Contact us with trainer compatibility questions. Bike Compatibility Many bike manufacturers do not publish thread pitch or hub spacing online. If you are unclear as to what type of thru axle your bike uses, please contact us.
The Saris thru axle adapter is designed for indoor use on Saris- or CycleOps-branded trainers only and should not be ridden outdoors. - Compatible with Classic series trainers and most Pro series trainers. Not compatible with PowerSync trainers. Contact us with trainer compatibility questions. - This adapter is designed to work with bikes that have a 142x12mm thru axle with 1.0 or 1.75 thread pitch. - The axle is threaded on both sides to fit both Syntace and Maxle/ABP style thru axle systems. - Many bike manufacturers do not publish thread pitch or hub spacing online. If you are unclear as to what type of thru axle your bike uses, please reach out to your local bike shop or the bicycle manufacturer directly. What's Included - Thru axle - Washers - End caps with bolts
The Saris thru axle adapter is designed for indoor use on Saris- and CycleOps-branded trainers only and should not be ridden outdoors. Compatible with current classic series trainers. Not compatible with the JetFluid Pro, SuperMagneto Pro, PowerBeam Pro, or PowerSync trainers. Contact us with trainer compatibility questions. - This adapter is designed to work with bikes that have a 142x12mm or 148x12mm thru axle with 1.0 or 1.75 thread pitch. - The axle is threaded on both sides to fit Syntace and Maxle/ABP style thru axle systems. - Many bike manufacturers do not publish thread pitch or hub spacing online. If you are unclear as to what type of thru axle your bike uses, please reach out to your local bike shop or the bicycle manufacturer directly. - Adapts a thru axle hub bike for a trainer - Only compatible with current basic trainers - Fits most 142-148mm thru axle bikes with 1.0 or 1.75 thread pitch
For a stable, worry-free ride with any rear wheel-mounted trainer. Product Features - For a stable, worry-free ride with any rear wheel-mounted trainer. - Unique 3-level design lets you select the level of difficulty. - Stack two blocks to simulate climbing workouts. Three different positions to raise your front wheel and simulate hill climbs - 2.1 inches (5.3 cm) - 2.7 inches (6.8 cm) - 3.1 inches (7.9 cm)
Adjust resistance on Mag trainer without leaving the saddle. - Quick Release mounting system fits most stems. - For use with the Mag bike trainer only
Trainer Mission Control Every training room needs a control center, and the TD1 is more than equipped for the job. Featuring built-in power strip with 2 AC and 2 USB outlets, this indoor trainer desk was designed to keep everything you need charged, organized and close at hand. Its roomy 12" x 20" table top is made from laminated birch for easy clean up, and is supported by stainless, corrosion-resistant steel sourced from America’s heartland. And as part of the Saris trainer eco-system, the TD1 is a perfect complement to the MP1 trainer platform. After just one ride with a dedicated trainer desk, you’ll ask yourself how you ever rode indoors without one. - Stay Charged: built-in power strip keeps training necessities nearby and powered up. - Pick Your Height: adjustable for wide range of bikes and training configurations. - Easy Cleaning: laminated birch wood top makes for easy clean-up post-ride. - Steamlined Look: built-in cable management and stainless steel hardware are both functional and eye-pleasing. - Enhanced Experience: a great addition to indoor training. Specs - Base: 13-inches wide x 36-inches Depth - Desk Top: : 12-inches Width x 20-inches Depth - Adjustable Desk Height from Floor: 40- to 55-inches - Materials: Laminated birch table top supported by a steel frame, featuring stainless steel and corrosion-resistant hardware - Cord Length: 6- foot AC cord - Built-in power strip with 2 AC and 2 USB outlets - Built-in cord retention clips for easy cable management and a clean look.
Everything you need for the best indoor trainer experience possible. - Can be used across a wide range of trainer setups. - Includes Trainer Mat, Climbing Block and Saris towel.
- Includes clutch knob and L-bolt - Basic Trainer Clutch Knob is compatible with any Wind, Mag, Mag+, Magneto or Fluid trainer that already uses L-bolt - Magnus Clutch Knob should only be used with Magnus Smart Trainer - Watch our video to learn more
Save Your Tires for Race Day Frequent trainer riders often find the tread on their rear wheel will wear down over time. We recommend using our trainer tires on our Saris indoor trainers. They are made of tough material that can stand up to hours and hours and hours of training. Product Features - 700c x 23 – 25 fits most road bikes. - Ultra-quiet and super-durable. - For use with an indoor trainer only.
Our Trainer Axle is designed to adapt your Surly MDS/Gnot Boost thru-axle-equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - This axle is for Surly bikes with the MDS/Gnot Boost system. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum, and hard-anodized for rugged durability. - No special tools required. Design allows for wheel installation or removal using your standard 5 mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.
The TPH-1 Tablet Grip from Minoura is the ultimate tablet holder for indoor training. Fitting a diameter between 28mm and 35mm, this stand will fit most bicycles. - Perfect accessory to use with LiveTraining Apps, The Sufferfest videos, or other media - SM clamp easily mounts or dismounts from the handlebar or tube - Spring-loaded clamp system is simple to use and securely holds your device in place - Holds from a 7.9 to 9.7 inch screen with 360 degree rotation system - Can mount to your repair stand so you can easily reference the Internet when working on your bike
$17.95 - $19.95
- Replacement belt - Select model based on model/roller size and belt size
Giant's Chopping Block lifts your front wheel so it's even with your rear wheel while on a trainer. It's compatible with 26-inch and 700c wheels and has a stable, anti-skid base.
The Giant Indoor Trainer Mat is the perfect noise-reducing floor protection for indoor training. - Rubberized material for easy rinse off after your workout - ‘Pebbled’ surface, anti-skid and scratch-resistant material protects flooring while working out - Extra-large 3’ x 6’ (91.5cm x 183cm) size covers entire workout area, prevents perspiration from getting on carpets or wood floors - Comes rolled-up in draw-string, mesh carry bag with shoulder strap
Of course you love your Omnium Trainer, but you’re left wondering how you could possibly love indoor cycling training even more. Easy, our non-slip and water-repellent (aka sweat) Floor Mat is designed to keep you safe and protect your floors while in your cycling cleats indoors. And because your cycling training plan asks for incredibly intense efforts, the Floor Mat can ensure firm contact with the ground and prevent movement during leg-busting intervals. Add a Sweat Guard to your indoor cycling collection and you’ve got a training party! - Non-slip surface keep you safe while in cycling cleats - Protects floors from sweat and bike grime - Water-repellent surface does what it was designed to do – keep sweat off your floor - Compress-ability ensures trainer stays put during intense efforts - Easily rolls up for storage - Cleans easily with soap and water - Absorbs noise and vibration - Enhances overall stability of any indoor trainer setup - 4mm (5/32?) thickness is optimal balance of support and storage
You’re already a proud owner of the Omnium Zero-Drive Bike Trainer, but today you’re looking for a sweat-inducing, intense workout. Designed to be lightweight and portable, the Omnium Trainer is adaptable to whatever bike you ride and whatever workout you’re targeting – let the Omnium Over-Drive Sled be your next training accessory. - Dynamic, free-floating rear wheel design promotes the most realistic riding experience of any stationary bike trainer - Patented, Internal Progressive Resistance via friction-less Eddy Current Technology - Parabolic, progressive resistance curve accurately simulates outdoor cycling (rolling + wind resistance) - Precision machined 4” aluminum rollers create a smooth and quiet ride - Adaptable to virtually any bike (up to 1348mm wheelbase with optional extender) - No tools required to assemble or store — simply unfold for use and fold for storage and travel - Maintenance-free resistance unit and roller bearings - Compatible with Zwift, The Sufferfest, TrainerRoad and Kinomap traditional trainer features* *Requires ANT+ or BT rear wheel speed sensor
The Elite Folding Mat increases the comfort of your home cycling setup while protecting the surfaces you train on every day. It's easy to use, store, and transport and can be stored everywhere in your house. Dimensions: 1.8m x .9m
- Sram XD and XDR freehub for Direct Drive trainers (Drivo and Direto's family, Suito, Turno, Kura, Turbo Roteo and Volano). - Compatible with 12 speed cassette.
The Gel Block is an indispensable accessory for perfecting your position on the bike and provides a more natural feel to your training. - Reduces vibrations on the handlebars for more comfortable training - Non-slip Elastogel insert ensures maximum stability and alignment of the front wheel - Suitable for road and MTB
Misuro B+ is the perfect sensor to enhance your training sessions with Elite home trainers and rollers. This ANT+ and Bluetooth Smart Speed/Power/Cadence sensor monitors indoor training sessions via smartphone, tablet, cycle computer, or compatible GPS devices when installed on an Elite trainer. - Reads data based on the type of trainer used. - Uses ANT+ and Bluetooth Smart protocols that are compatible with many devices. - When paired with the My E-Training Software, it turns your Elite trainer into an advanced digital instrument that displays and manages fundamental training data.
Protects the bicycle from sweat and avoids corrosions or rust. - Prevents an accumulation of sweat on the frame and components that would lead to corrosion or affect the finish - Sits above the top-tube and can be adjusted for different bicycles - Washing-machine friendly
This height-adjustable front wheel support can simulate both flat terrain and slopes perfectly - Unique design with 5 levels lets you adjust the height of your front wheel to simulate hill climbs up to 6% - Anti-slip rubber feet eliminate handlebar vibrations - Internal design that guarantees maximum wheel stability - Suitable for both road and MTB - You can attach to the trainer frame when not in use for easy transport and storage
Page 1 of 2 Next page